Preliminary Testing

Under the following circumstances, a white deposit may occur on the surface after the BONE DRY SURFA-SEAL dries:

1. surface was treated previously with different waterproofing materials
    
2. high acid levels in the building materials
    
3. surface too hot due to sun/ambient temperatures
    
4. nonporous surfaces not capable of being penetrated, i.e., glazed tile or brick, extremely dense brick, GFRC panels and the like

Since this deposit can only be removed by light sandblasting or other mechanical means, it is very important to test a small area to determine if any of these conditions exist prior to commencing a large scale application.

Preparatory Work

1. Repair all construction faults, except fine hairline cracks. Large cracks should be filled with a patching material that is compatible with the substrate. 
    
2. Clean surfaces thoroughly, removing all dirt, oils, grease and atmospheric latents that could inhibit full penetration of the BONE DRY SURFA-SEAL. Extremely dirty surfaces should be cleaned using high pressure with a mild, non-detergent cleaner. Caution: use only organic cleaners, as the residue from a detergent cleaner may reduce the effectiveness of the BONE DRY SURFA-SEAL.
    
3. Remove any efflorescence using a mild acid solution
    
4. Mask windows and all other adjacent surfaces that are not to be treated (i.e., wood, glass, aluminum and the like) Protect shrubbery and other plants near the treating area with dropcloths. Plastic dropcloths should not be used as the greenhouse effect may be detrimental to some vegetation. Protect vehicles and passersby from overspray.

Method of Application

1. On warm days where the temperature is 90 F or above, or where the surface to be treated has a direct sunlight exposure and is 90 F or greater, the surface must first be cooled down by lightly misting with cold water prior to the application of BONE DRY SURFA-SEAL.
   
   Caution: Do Not saturate the surface with water. Surface temperature can be approximated by laying a hand on the surface for several minutes. The objective of the cool-down is to prevent flash evaporation of the BONE DRY SURFA-SEAL before it has had a chance to penetrate into the surface. This may result in a white deposit being formed.
    
2. Agitate or stir the BONE DRY SURFA-SEAL solution to assure complete mixing of the material.
    
3. The surface should still be slightly moist from Step1 at the time of application. For best results, apply with low pressure spray equipment at approximately 80 to 250 square feet per gallon, depending upon the texture and porosity of the substrate.
   
   Low pressure spray equipment, such as a hand pumped garden type sprayer works well for medium sized areas. For large areas, airless spray equipment is very efficient. Small areas can be effectively treated using a spray bottle. Brushes or rollers are not recommended because of the low viscosity of the BONE DRY SURFA-SEAL
    
4. After application, allow 24 hours (recommended) for maximum development of repellency
    
5. If a second coat is necessary, it should be applied within 15 minutes of the first application. In extremely warm weather, reduce the size of the areas to be treated to allow for more rapid drying. If the surface dries too quickly, a second application may cause white deposits to occur on the surface.

Precautions

1. Wear protective clothing and eye protection. Wash hands immediately after handling. If contact with eyes occurs, flush thoroughly with clear water and seek medical attention immediately.
    
2. Avoid overlapping or running; keep a wet edge. Always pick off any rundowns with a dry roller or brush.
    
3. In some overlapping conditions, white deposits may occur as BONE DRY SURFA-SEAL dries. To remove, wipe with a damp cloth soon after forming. Delay in removing the deposit may necessitate removal by mechanical means.
    
4. Prevent BONE DRY SURFA-SEAL from contacting aluminum. If contact does occur, wipe immediately with a damp cloth to prevent etching.
    
5. Prevent BONE DRY SURFA-SEAL from contacting glass. When contact does occur, wipe immediately with damp cloth to prevent etching. If it should dry, remove with a razor blade.
    
6. When applied to brick walls, it is important to insure that water is not intruding behind the wall through any entrances such as leaking flashings, sills, copings or faulty caulk joints. In cold weather, spalling of the brick may occur due to the water freezing behind the waterproofed face of the brick.
    
7. If BONE DRY SURFA-SEAL should freeze, a crystalline structure may develop. This does not damage the material. Allow material to thaw at room temperature until a clear solution is achieved.

Availability

BONE DRY SURFA-SEAL is available exclusively through:

BONE DRY
6520 67th Street
Kenosha, WI 53142
262-564-8422

Warranty

The information and data contained herein are believed to be accurate and reliable; however it is the user’s responsibility to determine suitability of use. Since Prairie Shores, Ltd. cannot know all of the uses to Which its products may be put, or the conditions of use, it makes no warranty concerning the fitness or suitability of its products for any particular purpose. The user should thoroughly test any proposed use of our products and Independently conclude satisfactory performance for the given application. Likewise,l if the manner in which our Products are used requires agency or government approval user must obtain it. Prairie Shores, Ltd. warrants only That its products will meet its current specifications. There is no warrant of merchantability of fitness for use nor any other expressed or implied warranties. The user’s exclusive remedy and the sole lability of Prairie Shores, Ltd. is limited to refund of the purchase price or replacement of any product shown to be otherwise than as warranted. Prairie Shores, Ltd. will not be liable for consequential or incidental damages of any kind. Suggestions of previous users should not be taken as inducements to infringe on any patents.

Filing Systems

BONE DRY
6520 67th Street
Kenosha, WI 53142

“BONE DRY" Copyright 2005. All rights reserved. Printed in U.S.A.

testimonials

"Our firm is the property management arm of one of the largest shopping center development and construction firms in America. We have been very pleased with the results their products have given us in sealing troublesome areas."
- IMA Commercial Properties